Global Leader in Ice Thermal Storage
ESD-1000 SERIES (12 or 24 volts, hard potted)
ESD-1000 SERIES HUEGLI TECH AG
ESD-1000 (low cost speed control unit, single speed) Basic speed control with Gain and Speed adjustments plus Speed fine trim input.
ESD-2100 SERIES (12 and 24 volts servicable)
ESD-2100 SERIES HUEGLI TECH AG
ESD-2110 (low cost design, standard housing) Speed control with Gain and Stability setting, Speed adjustment plus Speed fine trim input.
ESD-2200 SERIES (12 or 24 volts hardpotted)
ESD-2200 SERIES HUEGLI TECH AG
ESD-2210 functions as ESD-2110, but hard potted for severe environments
ESD-5100 SERIES (12 and 24 volts)
ESD-5100 SERIES HUEGLI TECH AG
Basic unit, for single & parallel genset operation, includes full PID settings, idle and droop function.
- ESD-5111 (Idle, droop, accessory functions)
- ESD-5119 (Cummins EFC, reverse acting)
- ESD-5120 (Cummins EFC, forward acting)
- ESD-5160 (Cummins EFC, reverse acting)
ESD-5200 SERIES (12 and 24 volts)
ESD-5200 SERIES HUEGLI TECH AG
ESD-5300 SERIES (24 volts)
ESD-5300 SERIES HUEGLI TECH AG
Enhanced, analogue speed control for all types of GAC actuators, includes various features such as speed ramping, dual Gain switching for special engine applications (Gas, Hot/Cold etc.), starting fuel limitation, speed ramping, crank termination and overspeed protection. Full PID setting and droop / Idle operation.
- ESD-5330 (ramp generator, two speed switches, dual dynamic adjustments)
- ESD-5331 (Cummins EFC)
ESD-5400 SERIES (12 and 24 volts)
ESD-5400 SERIES HUEGLI TECH AG
As ESD-5111, includes full PID setting and droop / Idle operation plus position sensor feedback regulation loop.
ESD-5500 SERIES (12 and 24 volts)
ESD-5500 SERIES HUEGLI TECH AG
- ESD-5500E CE (standard unit)
- ESD-5522 CE (Cummins EFC)
- ESD-5550 CE (ESD-5500 with overspeed relay)
- ESD-5570 (as ESD-5550, Cummins EFC version)
ECC-326 SERIES HUEGLI TECH AG
The ECC-326 speed control unit is an all electronic device designed to control engine speed with precise response to transient engine loads changes. This closed loop speed control, when connected to a proportional actuator and supplied with a speed signal/ frequency from the main AC generator, will control a wide variety of engines in an isochronous mode.
- No pick-up signal required.
- Full PID setting
SDG 700 Series (Smart Digital Governor) - Unique
SDG 700 SERIES HUEGLI TECH AG
Includes all ESD 2210/5550 functions, but offers further customising possibilities for various kinds of all speed and fixed speed applications, including engine monitoring, fuel-limiting and various protection features, all accesable via CAN. End off line configuration via tamperproof on-board key-pad, no tool necessary. PC interface using GAC's SMARTVIEW software gives the user expanded programming, monitoring and diagnostics capability.
SDG 500 Series (Smart Digital Governor)
SDG 500 SERIES HUEGLI TECH AG
The SDG500 Series is designed to regulate engine speed on diesel and gas/gasoline reciprocating engines. The SDG 500Series is a suitable replacement for any mechanical system that needs more flexibility, precision or control in governing speed. The SDG500 Series is an integral part of a closed loop control. When connected to an electric actuator and supplied with a magnetic speed sensor signal, the governor will direct the engine to the desired speed setting. The SDG500 Series is designed for industrial applications ranging from generators and mechanical drives to pumps and compressors.
IGC Series, Digital Governor and Controller
IGC SERIES HUEGLI TECH AG
For constant or variable speed applications. Outputs for crank solenoid, fuel valve and preheat (3 Relays) Totally 9 discrete inputs configurable as switch type or 0-10 VDC. Remote starting, battery system monitor. PID loop for pump or compressor pressure control.
DSC 1000 SERIES HUEGLI TECH AG
Microprocessor based engine control for use with GAC and foreign actuators. Specially designed for the industrial and marine (classified) diesel- & gas-engine market.
- Total fuel management i.e. multiple torque- & pressure- based maps.
- Multiple droop & isochronous options
- End of line programming and field configurable design, simply via standard PC with GAC's GDS software.
- CAN bus data transfer (J1939) for total system integration.